PEEK-CLASSIX BC2-WH Granules

High performance biocompatible thermoplastic material, white compounded PolyEtherEtherKetone (PEEK), semi crystalline. Granules for injection moulding and extrusion, medium flow, suitable for medical devices that will be in contact with human tissue for 30 days or less. Colour white.

Typical Application Areas
For use in applications requiring high strength, high stiffness, and high ductility. Suitable for medical devices that will be in contact with human tissue for 30 days or less. As PEEK is hygroscopic, drying before use is recommended. Further information is available upon request.

PEEK-CLASSIX™ offers a high-performance polymer solution with a low level of extractables and leachables, and chemical resistance to drug concentrates, and the extremes found within the human body.

Request a quote Download PDF

Material Properties
Physical	Nominal Value	Unit	Test Method
Density (23°C)	1.39	g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (400°C/2.16 kg)	5.9	g/10 min	Internal Method
Spiral Flow¹	11.0	cm	Internal Method
Molding Shrinkage			ASTM D955
Flow	1.1	%
Across Flow	1.4	%
Water Absorption (Equilibrium, 23°C, 50% RH)	0.58	%	ISO 62
Crystallinity DSC	31.0	%	Internal Method
Mechanical	Nominal Value	Unit	Test Method
Tensile Stress (Yield, 23°C)	99.5	MPa	ISO 527-2
Tensile Strain (Break, 23°C)	18	%	ISO 527-2
Flexural Modulus (23°C)	4190	MPa	ISO 178
Flexural Stress			ISO 178
Yield, 23°C	164	MPa
3.5% Strain, 23°C	131	MPa
Impact	Nominal Value	Unit	Test Method
Notched Izod Impact Strength (23°C)	6.1	kJ/m²	ISO 180
Thermal	Nominal Value	Unit	Test Method
Glass Transition Temperature (Onset)	145	°C	ISO 11357-2
Melting Temperature	342	°C	ISO 11357-3
Recrystallization Temperature (Peak)	288	°C	ISO 11357-3
Fill Analysis	Nominal Value	Unit	Test Method
Melt Viscosity 1000 s^-1 (400°C)	398	Pa·s	Internal Method
Melt Stability 1000 s^-1, 1 hr (400°C)	0.91	%	Internal Method

Typical Processing Information
Injection	Nominal Value	Unit
Drying Temperature	120 to 150	°C
Drying Time	3.0 to 5.0	hr
Suggested Max Moisture	0.020	%
Hopper Temperature	< 100	°C
Rear Temperature	350	°C
Middle Temperature	355 to 365	°C
Front Temperature	370	°C
Nozzle Temperature	370	°C
Mould Temperature	170 to 200	°C
Injection Notes
Drying Temperature / Time: 150°C / 3h or 120°C / 5h (residual moisture <0.02%) Runner: Die / Nozzle >3 mm, Manifold >3.5 mm Gate: >1 mm or 0.5 x part thickness Important Notes: 1) Processing conditions quoted in our datasheets are typical of those used in our processing laboratories Data for mould shrinkage should be used for material comparison. Actual mould shrinkage values are highly dependent on part geometry, mould configuration, and processing conditions. Mould shrinkage differs for along flow and across flow directions. “Along flow” direction is taken as the direction the molten material is travelling when it exits the gate and enters the mould. Mould shrinkage is expressed as a percent change in dimension of a specimen in relation to mould dimensions. 2) Data are generated in accordance with prevailing national, international and internal standards, and should be used for material comparison. Actual property values are highly dependent on part geometry, mould configuration and processing conditions. Properties may also differ for along flow and across flow directions. Detailed data available on our website www.invibio.com or upon request.

Notes

¹1.00 mm

PEEK-CLASSIX™ BC2-WH (Granules)